Door Seal Brush: How to Block Dust and Drafts at Gaps
A door seal brush closes a gap with thousands of flexible filaments instead of a solid lip, so it can follow an uneven floor, a sliding leaf or a lift car in motion without jamming. That flexibility is also why the same brush seals well on one door and fails on another: the result depends on how far the bristles are deflected, which filament is used, and whether the holder stays straight along the whole opening. This guide covers the measurement, filament and mounting decisions behind a working seal on machine cabinets, elevator doors and automatic doors, and the cases where a brush is the wrong part for the job.
How a door seal brush blocks dust and drafts
A door seal brush is a strip of filament held in a rigid or semi-rigid backing and mounted so the tips touch, or almost touch, the surface on the other side of the gap. The barrier is not a single contact line. Air and the dust it carries have to travel between thousands of filaments, and every change of direction inside that pack costs energy. A short, dense filament makes the path harder to cross, which is why a correctly fitted strip cuts visible dust movement even though air still passes through.
The second part of the mechanism is deflection. Bristles bend instead of resisting, so a sliding leaf, a swinging door or a lift car that drifts a little off its guide can pass without crushing the seal. A rubber lip needs even contact along its full length, and when the floor rises at one end, the lip lifts at the other. A brush absorbs that variation locally, which is the main reason it suits long gaps on machine guards, roller shutters, cabinets and automatic doors.
There is a wiping effect as well. Because the filament touches the floor or the track, the brush sweeps grit away from the gap as the door moves. Set the filament so it trails the direction of travel. Bristles that lead the movement push dust into the opening rather than clearing it, and they tend to fold and set in that position.

A brush seal is not a filter and not a gasket. It reduces the flow of dust-laden air and blocks the larger particles, while very fine dust still passes through the filament pack. A pressure difference across the door pushes more of it through. Treat the brush as the first barrier and keep gaskets or sealed enclosures for the cases that need them.
Which filament suits your gap and environment
Filament choice decides how long the seal holds its shape, how much drag the door feels and whether the brush damages the surface it touches. A fine filament seals better at the same deflection because more filaments sit in each unit of length. A coarse filament survives abrasion and sharp edges but leaves larger openings between bristles. Crimped filament adds bulk and spring, which helps on wide or irregular gaps.
| Filament | Works well for | Check before you specify |
|---|---|---|
| Polypropylene | Indoor cabinets, automatic doors, general dust and draft control, damp floors | Softens sooner than nylon near motors or hot housings, and turns brittle in sustained cold |
| Nylon 6.6 | High cycle counts, sliding doors, abrasive grit, moderate heat | Higher cost, and it takes up moisture, so cut lengths can shift slightly |
| Anti-static nylon | Electronics enclosures, clinging dust, static-sensitive assemblies | A conductive filament does not make an area safe for combustible dust on its own |
| Crimped brass wire | Heat, static discharge paths, heavier dust loads | Scratches painted and anodized surfaces and can bridge electrical contacts |
| Stainless steel wire | Hot housings, coarse gaps, heavy grit, outdoor machines | Hard on floor finishes, noisy in sliding contact, rarely right for a pedestrian door |
Metal filament changes the calculation. Brass and stainless steel wire survive heat, grit and sharp edges that would wear out a polymer strip, and they can carry static to earth when the strip is bonded. They also scratch finishes, make more noise in sliding contact and may bridge electrical contacts, so they belong on machine and industrial door gaps rather than painted pedestrian doors.
Metal filaments solve heat and static problems but bring their own limits on painted surfaces. <what you know about brass wire brush strip> covers brass wire strip brush construction and where that filament is used.
Two properties matter more than the material name. The first is filament diameter: a fine filament and a coarse one behave differently in the same holder, and the finer one seals better while wearing faster. The second is density, the number of filaments packed into each unit of length. A dense strip costs more and seals better, while a sparse strip is easier to push through a tight gap but leaves visible openings.
Setting the gap, interference and mounting profile
Measure the gap before choosing anything. Take readings at both ends and the middle with the door closed, then add readings along the travel path for a sliding door. The largest reading sets the bristle length, and the difference between the largest and smallest reading tells you whether a straight strip can seal the opening or whether the holder needs packing or a stepped profile.
Interference is the amount by which the bristle tips are deflected by the opposing surface. Too little interference leaves a light gap that dust finds; too much loads the door operator, raises noise and sets the bristles permanently to one side. No universal figure applies, because a long soft filament deflects easily and a short stiff one does not. Set the tips just touching, run the door, then increase the deflection in small steps until a light test shows no gap and the door still moves with its normal force margin. I call this working range the interference window, and it is the most useful number to record for the next replacement.
The holder matters as much as the brush. An anodized aluminum profile suits indoor cabinet and door work, galvanized steel covers general machinery at lower cost, and stainless steel is the choice for washdown, outdoor and food areas. Fixing method follows the mounting surface: a push-fit profile for a prepared groove, a bolt-on profile where the frame can be drilled, and retaining clips where the strip may need to come out for cleaning. Adhesive mounting is unreliable on vibrating doors and on surfaces that see temperature swings.
Length and joints deserve attention. A strip supplied in one continuous piece has no leak path, so measure the opening and order the full length where transport allows. Where a joint is unavoidable, keep it away from the busiest part of the gap and close it with a cap or a short overlap. Corners need a mitred cut or a moulded corner piece, because two square-cut ends meeting at 90 degrees leave a triangular opening.
Huixi Brush cuts strip brushes to the measured gap length and matches the holder profile to the mounting surface, which removes the joint that a stock length would force into the middle of a door.
| RFQ field | What to send | Why it matters |
|---|---|---|
| Gap size | Length, height and the variation between three or more readings | A single average hides the wide point where dust enters |
| Motion | Sliding, swinging, roller shutter or lift car door, plus travel direction | Bristle angle and interference depend on how the door moves |
| Cycles | Openings per shift and expected service years | Sets the choice between polypropylene and nylon |
| Environment | Dust type, oil mist, washdown, outdoor exposure, heat sources | Oil and heat change filament stiffness and the cleaning method |
| Surface | Floor or frame material and finish | Metal filament scratches coatings that a nylon strip leaves intact |
| Compliance | Fire rating, static control or hygiene requirement | These decide whether a brush is allowed at all, and which assembly must be tested |
When the gap is not straight
Straight runs are the easy case. Formed strip brushes are shaped to a profile during manufacture, which suits a curved header or a recessed frame where a straight strip cannot sit flat. Flexible strip brushes use a bendable spine so the installer can follow a curve on site. For round openings, such as a shaft passing through a machine panel, a spiral brush wraps the shaft and closes the annular gap while the shaft turns.

The limit in all three cases is the same: bending a profile reduces its straightness, so check the fit against the actual frame rather than the drawing.
Elevator and automatic door details worth checking first
On a lift car door, the brush usually goes along the bottom edge, the vertical meeting edges, or both. The aim is to keep hoistway dust out of the car and to stop dirt being carried into the sill groove. Check three things before fitting. The brush must not touch the door operator, the safety edge or the landing door interlock. The bristles must not be able to catch on the sill or the car frame as the door moves. And the added drag must stay inside the force and kinetic energy limits that apply to the installation, since lift standards such as EN 81-20 treat door movement as safety-relevant [1].
On an automatic pedestrian door, the seal is often wanted for wind, leaves and street dust. The brush has to stay clear of the motion sensor pattern and the safety beam, and it must not slow the leaf enough to change the opening time. Mount the strip so the sensor sees the floor where it expects to, and test the door with the safety devices active rather than bypassed.
On fire-rated doors, a brush is not a fire seal. Intumescent strips and tested door assemblies do the fire work, and adding a brush to a certified leaf can affect that certification and the closing force. Ask the door manufacturer before changing a rated assembly. On equipment cabinets, a brush on the door edge reduces dust reaching the interior, but it does not turn the cabinet into an enclosure with a tested IP rating under IEC 60529 [2].
Any change to a machine guard or door also belongs in the risk assessment. Under ISO 12100, hazards created by moving parts and by modifications to the machine have to be assessed, and a brush that obstructs a guard, a light curtain or an interlock does not count as an improvement [3].
Fitting the brush so the gap closes without drag
- Record the gap. Measure at both ends, the middle and any point where the floor or frame changes level. Keep the numbers; they are the baseline for every later check.
- Choose filament and backing from the measured conditions, not from the previous part number. A replacement that copies an old brush also copies the reason it failed.
- Cut to length and finish the ends. Remove burrs from metal backings, fit end caps, and mitre corners so the two runs meet without a triangular opening.
- Trial fit with the door at rest. Slide a sheet of paper or a thin feeler along the gap; it should drag lightly along the whole length and never pass freely.
- Cycle the door and watch the bristles. Run a series of full cycles and check that no filament folds backwards, that the door reaches its normal speed and that the operator does not labour.
- Re-check after a week and after the first temperature swing. New bristles take a set, and a strip that sealed on the first day can open a light gap once the filament relaxes.
Slotted mounting holes make step six easier, because the strip can move a millimetre or two without redrilling the frame.
Inspection, cleaning and replacement checks
A brush seal usually fails slowly. The first sign is often a dust line at one end of the opening rather than a visible hole. Inspect the tips for flattening, the holder for straightness and the fasteners for looseness. Look at the floor for a polished wear track, which shows where the bristles are working hardest.
Cleaning depends on what the brush collects. Dry mineral dust lifts out with a vacuum and a soft brush. Oil mist mixed with dust forms a crust that stiffens the filament and holds particles against the gap, so clean it with a mild detergent, rinse and dry fully before refitting. Solvents that attack polypropylene or nylon will shorten the life of the strip.
Replacement is due when the tips have worn enough that the holder can no longer be adjusted to close the light gap, when bristles have broken out and reduced the density, or when cleaning no longer restores flexibility. Keeping the interference window from the first installation makes that decision measurable rather than a matter of opinion.
| Symptom | Likely cause | Check |
|---|---|---|
| Dust line at one end of the opening | Wider gap at that end or a bent holder | Measure the gap at three points with the door closed |
| Door slows or the operator trips | Too much interference or a stiff filament | Check closing force and current draw, then reduce interference |
| Bristles flattened to one side | Filament leading the travel direction or heat near the motor | Confirm direction and measure the local temperature |
| Crust on the tips | Oil or coolant mist mixed with dust | Clean with mild detergent and trace the mist source |
| Bristles breaking out | Abrasion from a rough floor or a sharp edge | Inspect the contact surface and the cut ends |
Brushes that keep tracks and sills clear
A seal only holds while the track stays clear. A cylindrical brush mounted across the sill opening sweeps grit off the track before the door leaf reaches it, and the same roller shape works on conveyor openings where material falls onto a running surface.

Narrow guide rails and sill grooves are harder to reach with a roller. A wheel brush with a thin profile fits into the groove and lifts packed dirt out of the corners without dismantling the track.

Flat thresholds, floor plates and platform edges collect a film that a strip brush pushes rather than lifts. A disc brush running parallel to the surface lifts that film and leaves the plate clean enough for the seal to work.

What a brush seal cannot do
A brush reduces dust and draft; it does not make an opening airtight. Air passes between the filaments, and the amount grows with the pressure difference across the door and with wear at the tips. Where a specification calls for a sealed enclosure, a gasket, a lip seal or a tested enclosure is the right component, and the brush can support it at the edges.
It is not a water seal. Splash and running water find the filament pack, and capillary action holds moisture against the frame. Washdown doors need a gasket or a squeegee lip, with a brush used above the water line.
It is not a fire, smoke or acoustic seal on its own. Fire performance comes from a tested assembly, smoke control from a gasket or a controlled pressure regime, and sound reduction from mass and from closing the leaks around the whole opening. A brush can close one leak path, and that is the extent of its contribution.
It is not a machine guard. A brush that blocks access to a nip point, a rotating shaft or a shear edge does not replace a guard, a light curtain or an interlock, and the risk assessment still applies [3].
Specify the gap, not just the brush
Tell us the gap length and height, the variation between your readings, the door type and travel direction, the cycles per day, the dust and moisture conditions, and any fire, static or hygiene requirement. With those fields we can match filament, density and holder profile to the opening instead of sending a standard strip that has to be adapted on site.
Huixi Brush, [email protected], +86 1580 0932 713.
FAQ
Does a door seal brush stop drafts completely?
No. A brush reduces the flow of air and the dust it carries, but air still passes between the filaments, and the gap at the tips opens as the brush wears. It works best as a first barrier on gaps that move or vary in size. Where a specification demands an airtight joint, pair the brush with a gasket or a lip seal and treat the brush as the part that handles the uneven sections.
How much interference should the bristles have?
No single figure applies, because it depends on filament length, diameter and stiffness. Start with the tips just touching the surface, run the door, and increase the deflection in small steps until a light test shows no gap along the opening. Stop before the door slows, sounds different or needs more force. Record the setting, because it is the number you will want at the next replacement.
Can I add a brush to a fire-rated door?
Only with the door manufacturer’s agreement. The fire performance of a rated door comes from a tested assembly, usually including an intumescent strip, and an added brush can change the certification and the closing force. A brush may be acceptable as a draught and dust detail on a non-rated door, or where the assembly was tested with it. Check before drilling.
Why does dust still collect in one corner?
Gap variation is the usual reason. Floors slope, frames are not square, and a single straight strip cannot follow every change, so one corner ends up with less interference than the rest. Measure the gap at both ends and the middle, then pack the holder, fit a stepped profile or add a corner piece. A joint between two strips can produce the same effect.
References
[1] EN 81-20:2020, “Safety rules for the construction and installation of lifts — Lifts for the transport of persons and goods — Part 20: Passenger and goods passenger lifts,” CEN, 2020.
[2] IEC 60529:1989+AMD1:1999+AMD2:2013 CSV, “Degrees of protection provided by enclosures (IP Code),” International Electrotechnical Commission, 2013.
[3] ISO 12100:2010, “Safety of machinery — General principles for design — Risk assessment and risk reduction,” International Organization for Standardization, 2010.
If you’re interested, check out these related articles:
main features and applications of hx nylon cylindrical brush
brushes for steel wire industries cleaning descaling derusting polishing











